THE ULTIMATE
Preheat function: in power-off state, keep holding “+” end and fire button till the M1 mode appears; press the fire button 3 times to “Power”, and press “+” or “-” end to adjust the wattage of preheat; press the fire button again to “Time”, and press “+” or “-” end to adjust the second of preheat or to turn off the preheat function.
Function of charging cell phone: screw an RC adapter (not included) on the device and connect it with a cell phone by a USB cable. When the device is powered on, press the fire button once to start to charge the cell phone. Function of charging other e-cigarette mod: screw an RC adapter (not included) on the device and connect it with another e-cigarette mod by a USB cable. In power-off state, keep holding “+” end and fire button till the M1 mode appears; press the fire button 5 times to “USB” interface, and press “+” or “-” end to turn on or off this function. When the “USB” is turned on, 5 clicks of the fire button to power on the device, and in USB Charge mode, press fire button once to start to charge other e-cigarette mod. Adjust wattage: in TC-Ni/TC-Ti/TC-SS/TCR(M1,M2,M3) mode, the output wattage can be adjusted from 1W to 220W. Press the fire button 4 times in quick succession to enter the wattage setting menu and press “+” or “-” end to increase or decrease the wattage level. Keep pressing “+” or “-” end without looseness to rapidly increase or decrease the wattage level. Adjust temperature: in TC-Ni/TC-Ti/TC-SS/TCR(M1,M2,M3) mode, temperature can be adjusted from 100-315℃ or 220-600℉ by pressing “+” or “-” end, “+” end to increase and “-” end to decrease. Each press of the “+” or “-” end will increase or decrease the temperature setting by 5℃ or 10℉. Keep pressing “+” or “-” end without looseness can rapidly increase or decrease temperature setting. Shift between ℃ and ℉: if you increase the temperature to 315 ℃, and continue to press the “+” end, the temperature reading will automatically change to the lowest Fahrenheit (220℉). Equally, if the temperature is set at the lowest Fahrenheit (220℉) and you continue to press the “-” end, the temperature reading will automatically change to the highest Celsius (315 ℃). Lock/Unlock resistance: In TC-Ni/TC-Ti/TC-SS/TCR(M1,M2,M3) mode, when the device is powered on, keep pressing the fire button and “+” end simultaneously for two seconds to lock or unlock atomizer “base resistance”. The lock sign will appear when resistance is locked and “Ω” symbol will come back when unlocked. Note: 1. Please lock the resistance when the coil is at room temperature so that the device can display the correct “base resistance”. 2. In resistance lock mode, when you remove the coil and then put it back, the device can maintain the same “base resistance” although the coil resistance may increase due to the rise of temperature. In resistance unlock mode, when you remove the coil and then put a coil back, the screen may display “New coil up same down” as the coil resistance may increase within certain range. If it is the same coil, press the “-” end and if it is a new coil, press the “+” end. But please unlock the resistance when you want to change an atomizer or a coil of different resistance. 3. When using a common coil or a coil whose resistance is above 1.5ohm in TC-Ni/TC-Ti/TC-SS/TCR(M1,M2,M3) mode by mistake, the device will automatically switch back to VW mode.
7 Comments
Power on/off: push forward to open the battery cover, put two high-rate 18650 batteries in correct way into the device and finally close the battery cover. The device can be powered on or off by pressing the fire button 5 times. The battery levels of battery 1 and battery 2 are respectively displayed on the screen.
Note: 1. Please be careful not to use batteries with torn casing as it is a safety hazard. 2. Please make sure you are using high-rate 18650 batteries whose continuous discharge current should be above 25A. 3. Before using, please set the wattage within a proper range that the atomizer you installed can work with. Vaping: when the Eleaf iKonn 220 is powered on, long press the fire button to take a puff. Stealth on/off: press the fire button and “-” end of the adjustment button simultaneously when the device is powered on to switch between Stealth On and Stealth Off mode. In Stealth On mode, you can vape with the OLED screen off and you can press the fire button once to see current setting. Adjustment button lock/unlock: keep pressing “+” end and “-” end of the adjustment button simultaneously for two seconds when the device is powered on, then the adjustment button will be locked and the screen will display “Key Lock”. In the same way, the adjustment button can be unlocked and the screen will display “Key Unlock”. Through this operation, you can protect the buttons from unintentional presses and prolong their lifespan. Switch display mode: keep pressing “+” end and “-” end simultaneously for two seconds when the device is powered off, the screen display will rotate 180 degrees. You can view the screen from two different angles through this operation. Switch display interfaces: in power-on state, choose VW mode; keep holding “+” end and fire button till the current interface flashes; when it’s flashing, press “+”or “-” end to switch among different interfaces; finally press fire button once to confirm the interface you chose. Note: the interface can only be changed and selected under VW mode in power-on state. And when one interface is selected under VW mode, the interfaces of TC (Ni, Ti, SS, M1, M2, M3) modes will change accordingly and automatically. There are some advices about changing the coils and filling the atomizer of Eleaf iKonn 220 with ELLO kit, I recommend that you empty any E-Liquid in the Ello tank before changing coils
To change the coil
|
iStick.orgwww.istick.org is a Eleaf iStick Vape online Store, which is Eleaf official Authorized dealer online store, promise all products are 100% original and you can enjoy a perfect customer service. Archives
April 2018
Tags
All
|